供王利|泰科|松下 PANASONIC）|欧姆龙 OMRON）|芬德 FINDER 继电器Y90-SS-112D,完全代替王利T9AS5D12-12,深圳上海北京现货价格

T9AP1D52-12
T9AP1D52-24
T9AP1D52-48
T9AP5D52-12
T9AP5D52-24
T9AP5D52-48
T9AS1D12-110
T9AS1D12-12
T9AS1D12-18
T9AS1D12-24
T9AS1D12-48
T9AS1D12-5
T9AS1D22-110
T9AS1D22-12
T9AS1D22-24
T9AS1D22-48
T9AS1D22-5
T9AS1L12-12
T9AS1L12-24
T9AS5D12-110
T9AS5D12-12
T9AS5D12-18
T9AS5D12-24
T9AS5D12-48
T9AS5D12-5
T9AS5D22-110
T9AS5D22-12
T9AS5D22-24
T9AS5D22-48
T9AS5D22-5
T9AS5L12-12
T9AS5L12-24
Operate Data @ 25°C
Must Operate Voltage: 75% of nominal voltage or less.
Must Release Voltage: 10% of nominal voltage or more.
Operate Time (Including Bounce)§: 15 ms, max.
Release Time (Including Bounce)§: 15 ms, max.
§ At or From Nominal Coil Voltage
Low Cost
30 Amp PC Board or
Panel Mount Relay
File E22575
File LR15734
Contact Ratings @ 25°C with relay properly vented.
Remove vent nib after soldering and cleaning.
Arrangements: 1 Form A (SPST-NO), and 1 Form C (SPDT).
Material: Silver-cadmium oxide.
Mechanical Life: 10 million operations, typical.
Minimum Contact Load: 1A @ 5VDC or 12VAC.
Initial Contact Resistance: 75 milliohms, max., @ min. rated current (switched).
Initial Dielectric Strength
Between Open Contacts: 1,500V rms.
Between Contacts and Coil: 2,500V rms.
6 kV surge using 1.2μs/50μs Impulse Wave or
.5μs – 100kHz Ring Wave
Initial Insulation Resistance
Between Mutually Insulated Elements: 109 ohms, min., @ 500VDC,
25°C and 50% R.H.
Coil Data @ 25°C
Voltage: 5 to 110VDC.
Nominal Coil Power: 1.0W, (approx.) and 900mW (approx.) versions.
Maximum Coil Power: 2.8 Watt.
Maximum Coil Temperature(5): Class F: 140°C.
Duty Cycle: Continuous.
Nominal DC Resistance Nominal Nominal DC Resistance Nominal
Voltage ± 10% (Ohms) Current (mA) Voltage ± 10% (Ohms) Current (mA)
5 27 185 22 545 40
6 40 150 24 660 36
9 97 93 28 890 31
12 155 77 36 1,450 25
15 256 59 48 2,560 19
18 380 47 110 13,450 8
20 450 44
Coil Data - 900mW
Coil Data - 1 Watt
Nominal DC Resistance Nominal Nominal DC Resistance Nominal
Voltage ± 10% (Ohms) Current (mA) Voltage ± 10% (Ohms) Current (mA)
5 25 200 18 324 56
6 36 167 22 484 45
9 81 111 24 576 42
12 144 83 48 2,304 21
15 225 67 110 12,100 9
Features
? Up to 30 amp switching in SPST and 20 amp in SPDT arrangements.
? Immersion cleanable(6), plastic sealed case available.
? Meets UL 873 and UL 508 spacing – 1/8" through air, 1/4" over surface.
? Load connections made via 1/4" Q. C. terminals and safety wells accept
insulated female Q. C. terminals (mounting codes 2 & 5).
? UL Class F insulation system standard.
? Well suited for various industrial, commercial and residential applications.
Typical Electrical Load & Life - 900mW Coil
Contact Contact Load Type of Load Operations
Arrangement
1 120VAC 50 LRA/16 FLA 100,000
120VAC 30 LRA/11 FLA 200,000
Typical Electrical Load & Life - 1 Watt Coil
Contact Contact Load Type of Load Operations
Arrangement
1 30A @ 240VAC UL General Purpose 100,000
25A @ 240VAC Resistive Heater 100,000
5 20A/10A @ 240VAC UL General Purpose 100,000
20A/10A @ 240VAC UL Resistive 100,000
20A/10A @ 28VDC Resistive 100,000
UL 508/873 & CSA Contact Ratings - 1 Watt Coil
Voltage Load Type N.O. Contact N.C. Contact
277VAC Tungsten * 5.4A –
277VAC Ballast 10A 3A
240VAC Motor 2 HP 1/2 HP
240VAC Resistive * 30A 20A
240VAC General Purpose? 30A 15A
240VAC LRA/FLA **?? 80A/30A 30A/12A
240VAC Pilot Duty * 470VA 275VA
125VAC Motor 1 HP 1/4 HP
120VAC LRA/FLA 98A/22A –
120VAC Tungsten * 8.3A –
120VAC Pilot Duty 470VA –
28VDC Resistive 20A 10A
* Rated 6,000 operations.
** Higher UL & CSA ratings available.
? For Form C application, derate current to 20A (N.O.), 10A (N.C.).
?? For Form C application, derate current to 67%.
Note: Consult factory for other 900mW version contact ratings.
61
Mechanical Data
Termination: Printed circuit and quick connect terminals (4).
Enclosures (all have 94V-0 flammability rating):
T9AP: Unsealed, plastic dust cover.
T9AS: Immersion cleanable, sealed plastic case (2 & 3).
T9AV: Vented, flux-tight, plastic cover.
Weight: Q.C. version: 1.2 oz. (33g) approx. (mounting code 2 & 5).
Sealed Model T9AS: 0.9 oz. (26g) approx. (mounting code 1).
Notes
(1) Operating ambient temperature must consider “Must Operate Voltage
Change Over Temperature,” Contact Temperature Rise, Coil Temperature
Rise (If coil is not allowed to cool) and Maximum Coil Temperature.
Specification ambient considers 20A load with coil cooled to ambient.
(2) Sealed relay terminals should not be bent.
(3) Remove knock-off nib after cleaning process for optimum life of sealed
relays.
(4) Maximum soldering temperature is 500°F for 4 seconds.
(5) Class F coils are UL systems approved for maximum coil temperature of
140°C, by change of resistance method.
(6) See application note 13C265 for proper relay mounting, termination,
cleaning and PC board conductor width. Coil rise test performed with 30A
PC board to maintain 20°C maximum rise @ 30A.
T9AP1D52-12
T9AP1D52-24
T9AP1D52-48
T9AP5D52-12
T9AP5D52-24
T9AP5D52-48
T9AS1D12-110
T9AS1D12-12
T9AS1D12-18
T9AS1D12-24
T9AS1D12-48
T9AS1D12-5
T9AS1D22-110
T9AS1D22-12
T9AS1D22-24
T9AS1D22-48
T9AS1D22-5
T9AS1L12-12
T9AS1L12-24
T9AS5D12-110
T9AS5D12-12
T9AS5D12-18
T9AS5D12-24
T9AS5D12-48
T9AS5D12-5
T9AS5D22-110
T9AS5D22-12
T9AS5D22-24
T9AS5D22-48
T9AS5D22-5
T9AS5L12-12
T9AS5L12-24
Stock Items – The following items are normally maintained in stock for immediate delivery.
0
20
40
60
80
100
120
140
60 80 100 120 140 160 180
0A
10A
20A
30A
Sealed Relay, Vented (note 3)
PC Terminals For Coil & Contacts
Applied Continuous Coil Voltage (% of Rated Voltage)
Max. Alowable
Ambient Temp. (°C)
40
60
80
100
120
140
60 80 100 120 140 160 180
Relay With Dust Cover,
Flange Mount
0A
10A
20A
30A
Applied Continuous Coil Voltage (% of Rated Voltage)
Max. Alowable
Ambient Temp. (°C)
0
20
40
60
80
100
120
140
60 80 100 120 140 160 180
Sealed Relay, Vented (note 3);
Load Connections Via Q.C. Terminals,
PC Mount
0A
10A
20A
30A
Applied Continuous Coil Voltage (% of Rated Voltage)
Max. Alowable
Ambient Temp. (°C)
Environmental Data
Storage Temperature Range: -55°C to 130°C.
Operating Temperature Range(1): -55°C to +85°C.
Vibration, Operational: 0.065" (1.65mm) max. excursions from 10-55 Hz.
with no contact opening >100μs.
Shock, Operational: 10g for 11 ms with no contact opening >100μs.
Shock, Mechanical: 100g.
Ambient Temperature vs. Coil Voltage - 1 Watt Coil
Data below are average values and should be verified in application. Tests
were conducted within a 2' (.6 m) cube (still air); at nominal coil power @
25°C; with normally open contact loaded; and with 4' (1.22 m) long, #10
AWG load wires. P.C. board relays were mounted to a 30A, single side P.C.
board (6).
Ordering Information
Typical Part Number B T9A S 5 D 2 2 -12
1. Basic Series:
T9A = Low cost, printed circuit board/panel power relay.
2. Enclosure:
P = Unsealed, plastic dust cover (mounting code 5).
S = Immersion cleanable, knock off nib, sealed plastic case (mounting codes 1 & 2).
V = Vented, flux-tight (mounting code 1).
3. Contact Arrangement:
1 = 1 Form A (SPST-NO). 5 = 1 Form C (SPDT).
4. Coil Input:
D = DC voltage (1 Watt) L = DC voltage (900mW)
5. Mounting & Termination:
1 = Printed circuit board mounting; PC terminals for coil & contacts (a).
2 = Printed circuit board mounting; PC terminals for coil & contacts, and .250" (6.35mm) quick connects for contacts (b).
5 = Flanged mounting; .187" (4.75mm) quick connects for coil and .250" (6.35mm) quick connects for contacts (c).
6. Contact Material:
2 = Silver-cadmium oxide.
7. Coil Voltage:
5 = 5VDC 9 = 9VDC 15 = 15VDC 20 = 20VDC 24 = 24VDC 48 = 48VDC
6 = 6VDC 12 = 12VDC 18 = 18VDC 22 = 22VDC 36 = 36VDC 110 = 110VDC
a) Only available with enclosure code “S” & “V”. b) Only available with enclosure code “S”. c) Only available with enclosure code “P”.
T9AS/V – Mounting & Termination Code 1
.300
(7.62)
.100
(2.54)
.150
(3.81)
.500
(12.7)
.550
(13.97)
.700
(17.78)
.043 ± .003 DIA.
(1.09 ± .08)
.081 ± .005 DIA.
(2.06 ± .13)
.600
(15.24)
.212 MAX.
(5.38)
PC Board Layouts (Bottom Views)
T9AP/S – Mounting & Termination Code 2
.140 MAX.
(3.56) .250 MAX.
(6.35)
.300
(7.62)
.100
(2.54)
.150
(3.81)
.500
(12.7)
.550
(13.97)
.700
(17.78)
.043 ± .003 DIA.
(1.09 ± .08)
.081 ± .005 DIA.
(2.06 ± .13)
.600
(15.24)
T9AS/V – Mounting & Termination Code 1
Outline Dimensions
T9AP – Mounting & Termination Code 5
DIN Mount Adapter - 9T91A001
Wiring Diagrams (Bottom Views)
1.67
(42.41)
.50
(12.7) .50
(12.7)
.20
(5.08)
.40
(10.16)
.79
(20.06)
3 Holes for #6-32 Screw
0.011 Deep
(.27)
Note: Fits 35mm din track
Includes: 2 Din clips
2 Screws
Must be ordered in multiples of 50
1 Form A
T9AS – Mounting & Termination Code 2
1 Form C
.187 x .020
(4.75 x .508)
QUICK
CONNECT
1.080 MAX.
(27.43)
1.980 MAX.
(50.29)
1.713 ± .010
(43.51 ± .25)
.071 (1.80) RAD. FOR #6 SCREW
1.280 MAX.
(32.51)
1.100 MAX.
(27.94)
.250 x .032
(6.35 x .81)
QUICK
CONNECT
NCNO
COM
Note: Recommended mounting screw torque is 4.0-5.0 lbs.in when #6 screw is used.
.032 x .062
(.81 x 1.57)
.045 x .045
(1.14 x 1.14)
.03
(.80)
2 **CES
.250 x .032 QUICK
(6.35 x .81) CONNECT
NCNO
COM
1.280 MAX.
(32.51)
1.080 MAX.
(27.43)
.130 ± .020
(3.30 ± .51)
1.100 MAX.
(27.94)
?
.032 x .062
(.8 x 1.6)
TERMINALS
.212 MAX.
(5.38)
.10 MAX.
(2.54)
.045 x .045
(1.14 x 1.14)
TERMINAL
.805 MAX.
(20.4)
.69
(17.6)
1.280 MAX.
(32.51)
1.08 MAX.
(27.43)
.50
(12.8)
.03
(.80)
TERMINALS
.130 + .016
– .010
3.30 + .41
( –.25)
?
.016
(.43)